Size 5 FIFA Basic Football Club Hybrid - White
Store Availability
We have designed the FIFA-approved Club Hybrid ball, which pairs comfort with robustness, for your training sessions and competitions.
Need a ball for your football club? With the FIFA Basic Club ball, you get 2 layers of foam, making it more comfortable, and invisible seams for robustness.
BENEFITS
Bounce
Your ball complies with FIFA requirements in terms of bounce.
Robustness
Achieved a rating of 2.27 on a protocol-based test. Seams on the inside.
Lasting air retention
11% pressure loss in 14 days.
Stable flight
Achieved a rating of 5.96 on a protocol-based test. Classic 32 panels.
TECHNICAL INFORMATIONS
The story behind this ball
Our design team created this hybrid ball after observing football players in action on the pitch.
This ball is a hybrid because its design combines the comfort of a machine-stitched ball with the robustness of a hand-sewn one (the seams are on the inside).
We've also used a special bladder (2 km of thread is wrapped around it) to ensure robust inflation and better sphericity.
The robustness of our balls
We've developed a tool for characterising the robustness of our balls.
Defects that appear in use are identified and assessed through a series of laboratory tests.
These tests enable us to compare the overall strength of our footballs with those available on the market.
Our aim: to have the most robust products on the market.
Too light? Too heavy? The weight is standardised...
This ball weighs between 410 g and 450 g (size 5) and complies with official FIFA standards.
FIFA Basic approved.
How big is it? What's the circumference?
This ball measures between 68.0 cm and 70.0 cm and complies with official FIFA standards.
FIFA Basic approved.
A "round" ball?
Here's how we test sphericity:
Average measured variation: 1.8% max (FIFA Basic certification).
We measure the football's sphericity at 4500 different points and then examine any differences.
If the discrepancy is greater than 1.8% (FIFA Basic Standard), our engineers are tasked with improving the sphericity to ensure a consistent bounce.
Maximum pressure loss test: here's what we do...
Here's how we test pressure loss: We inflate the ball to the recommended pressure (meaning 0.8 bar).
72 hours later, the ball must not have lost more than 15% of its pressure, meaning approx. 0.1 bar (FIFA Basic certification). The pressure after 72 hours must, therefore, be at approx. 0.7 bar.
This also means that it is quite normal for a ball to lose pressure after a few days.
We've also tested how much water the ball absorbs...
Here's how we test water absorption:
We simulate rainy playing conditions in a lab, leaving the ball to sit in 2 cm of water on a pivoting support whilst subjecting it to 250 compressions.
At the end of the test, the ball must have absorbed no more than 15% of its weight (FIFA Basic certification).
It's all about the bounce
Here's the bounce test:
The ball is dropped onto a steel plate 10 times from a height of 2 metres.
The bounce height must be between 125 and 155 cm with a maximum difference of 10 cm between the ball's highest and lowest bounce.
Not even a scratch!
The most stringent test we put this ball through is the shooting machine test.
The ball must resist 2,500 shoots against a concrete slope at 50 km/h at a distance of 2.5 m.
At the end of the test, we check:
- the ball's general state: stitching must withstand this test
- the circumference: It must not have increased more than 1.5 cm.- the sphericity: it must not have varied by over 1.8%
- the pressure: loss of pressure must not exceed 12.5%.
How about you? What do you think?
We value your feedback and use it to continuously improve our products.A huge thank you in advance for sharing your feedback with us.
The story behind our range of balls
Our range of balls has been co-designed with 244 European footballers. This community helped us to pick the colours and names so that it's easy to see the difference between the models.
These balls are FIFA approved and designed to meet different levels of technical requirement (Training, Club, Match, Pro Ball).
Their increased robustness and better feel bring them ever closer to the official ball that graces the pitches of the Ligue 1 Uber Eats and Ligue 2 BKT.
composition
composition
Outer shell: 100.0% Polyurethane; Foam: 100.0% Ethylene Vinyl Acetate; Bladder: 70.0% Dry Rubber, 30.0% Bromo Isobutylene Isoprene Rubber; Laminated fabric: 100.0% Polyester
Tips for storage and maintenance
DO NOT WASH.
BLEACHING EXCLUDED.
DO NOT TUMBLE DRY.
DO NOT IRON.
DO NOT DRY CLEAN.
Storage tips
After use, store your ball in a dry and ventilated place.
Restrictions on use
Avoid contact with prickly objects or materials.
TESTS AND WARRANTY
Test product
Compliant with international football federations' most stringent standards.Certified to FIFA Basic standards.
Warranty
2 Years
Agree by
FIFA.